MENU
0
RECENTLY ADDED ITEM(S)

    You have no items in your shopping cart.

    TOTAL: $0.00
    CHECKOUT
    VIEW CART

    How to Install for a Sprinter 170 the Adventure Wagon Base Conversion Kit

    This guide is for installing the entire Adventure Wagon Interior kit in a 2007-present 170 Sprinter Van. There are a few differences with electrical installation between the NCV3 (2018-) and VS30 (2019+) sprinters for electrical wiring and it will be noted below.   Also the guide is targeted for Crew and Cargo version vans. If you have a Passenger van there will be some customization required in the ceiling for Air Conditioning units as well as leaving the rear wall panels off where windows are present. Please call one of our installers or our tech support team for more information on passenger installs.

    Any additional written build notes below will be the most up-to-date instructions and the video should be used as a baseline.

    Installation can be done over four days. It helps to have two people for A-frame bracing, track and panel installation.

    • Day 1: Van preparation, Install fans, run electrical harness, install Hushmat
    • Day 2: A-Frame bracer installation
    • Day 3: Insulation, Reinstall front headliner, Finish electrical wiring under the seatbase to the battery.
    • Day 4: Wall panel and track installation, reinstall B-Pillar covers and driver seat

    Step 1:

    Tools, Van Preparation and Disassembly

    Kit Unpacking

    Additional Tools Needed

    Rear Headliner/Walll

    Front Headliner Removal

    Door Panel Removal

    Step 2: Ceiling Fan Installation

    Fan Unboxing

    Fan Install

    Rear fan in a Sprinter 170

    Step 3: Run Electrical Harness

    Electrical Unboxing

    Running Cabin Harness

    Install End Connectors

    Step 4: Hushmat Installation

    Hushmat Unboxing

    Hushmat Install

    Step 5: A-Frame Wall and Ceiling Bracer Installation

    The heart of our Interior system is our A-Frame wall bracers and ceiling struts. We have modified how the wall bracers get installed please see our additional notes:

    • NOTE: We have learned that 2019-2020 Sprinters have significant inconsistencies in the location of the ceiling cross braces which can cause our A-frame to be installed incorrectly. If your cross braces are not centered (see photos) DO NOT use the alignment tools as shown in the video. Please call for installation instructions.
    • We are no longer using the magnets to align the wall bracers, instead we use set screws included with your kit.
    • If you've used self tapping set set screws to temporarily hold the wall track in place, please remove once the track is fastened to ensure the L track lays flat against the wall bracer
    • Be careful when drilling vertical wall bracer holes that you do not accidentally clip the wiring harness. To avoid this you can temporarily pull out the electrical harness.
    • Do not install your upper wall Thinsulate insulation until after your wiring chase is installed to avoid leaving shavings in the insulation

    A-Frame wall bracer unboxing Sprinter 144

    A-Frame wall bracer installation Sprinter 170

    Tutorial: using set screws for mounting

    Vertical wall bracer install for bed only 144

    Ceiling unboxing 144 & 170

    A-Frame ceiling 170

    Ceiling Wiring Chase 170

    Ceiling Unboxing 170 (old)

    Rear Door / Slider Door Rivetnuts

    Step 6: Insulation

    Insulation Kit Unboxing 170

    Insulation Install 170

    Step 7: Electrical Wiring Driver Seat Base

    The instructions to complete the electrical wiring under the driver seat base will vary based on what year van you have and whether or not you have the factory auxiliary battery. The Adventure Wagon harness and cabin connections are all the same, what changes is how to connect to your chosen battery under the driver seat.

    The Adventure Wagon electrical kit also allows you to connect to solar panels and cabin batteries such as the Goal Zero Yeti, Inergy Apex and Battleborn lithiums. Please call our customer support team for more product information and wiring diagrams.

    2019+ Sprinter connecting to the Starting battery

    2019+ Sprinter connecting to the Auxiliary battery

    2018- Sprinter connecting to the Starting battery

    2018- Sprinter connecting to the Auxiliary battery

    Step 8: Final Assembly

    Panel and Track Install

    Front Headliner

    Seat Installation